/* Soil Sensor Firmware
 * Sensiplicity Systems
 * 
 *  Copyright 2015
 * 
 *  Department of Botany and Plant Pathology
 *  Center for Genome Research and Biocomputing
 *  Oregon State University
 *  Corvallis, OR 97331
 * 
 * This program is not free software; you can not redistribute it and/or
 * modify it at all.
 * 
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. */

/* 
 * This firmware has several duties:
 *   -Measure...
 *      -Temperature within the soil
 *      -Ambient temperature and humidity
 *      -Soil moisture, in several zones
 *      -Light level
 *      -Current Vcc
 *      -Time since last reset
 *   -Report (over the Sense/Net RS-485 Bus)...
 *      -All measurements
 *      -Unique ID, when enumerating
 *   -Blink an LED when commanded.
 *   -Update firmware over the Sense/Net bus
 */
#include <avr/interrupt.h>
#define F_CPU 2000000UL /* 16Mhz crystal / 8. */
#include <util/delay.h>
#include <stdint.h>
#include <util/atomic.h>
#include "bus.h"
#include "light.h"
#include "humidity.h"
#include "time.h"
#include "moisture.h"

#include <stdio.h>
#include <string.h>

#ifndef BREV
#error "No board revision specified. Please provide -DBREV=2 or -DBREV=4 on the command line."
#endif

#if BREV != 2 && BREV != 4 && BREV!=5
#error "Incorect board revision specified. Please provide -DBREV=2, -DBREV=4, or -DBREV=5 on the command line."
#endif

/* Setup pins and peripherals.
 * Returns 0 on success, -1 on error. */
int init(void){
	init_led();
	init_timer();
	init_bus();
	init_i2c();
	init_adc();
	
	//TODO: Check for response from peripherals
	
	/* Shutdown unused SPI peripheral to save power. */
	PRR |= _BV(PRSPI);
	
	/* Set unused pins as outputs to save power.
	 * This is disabled for now because node 0x2625FF756E6B6E6F77
	 * has a short on one of these pins. */
// 	DDRD |= _BV(PD5) | _BV(PD6) | _BV(PD7);
// 	DDRE |= _BV(PE1);
// 	DDRC |= _BV(PC2) | _BV(PC3);
	
	sei();
	return 0;
}
	

int main(void){
	init();
	while(1){
		uint16_t u16;
		int16_t i16;
		uint8_t u8;
		
		measure_light(&MeasurementData.light);
		measure_humidity();
#if BREV == 2
		i16 = get_soil_temp_old();
#elif BREV == 4
		i16 = get_soil_temp(0);
#endif
		ATOMIC_BLOCK(ATOMIC_RESTORESTATE){
			MeasurementData.temp_soil = i16;
			MeasurementData.mtime = get_uptime();
		}
		
		_delay_ms(150);
		if(read_humidity(&u16, &i16)){
			set_led(LED_RED);
		}
		ATOMIC_BLOCK(ATOMIC_RESTORESTATE){
			MeasurementData.temp_ambient = i16;
			MeasurementData.humidity = u16;
		}
		
		u8 = get_vcc();
		
		ATOMIC_BLOCK(ATOMIC_RESTORESTATE){
			MeasurementData.volt_idle = u8;
			MeasurementData.volt_send = 0;
		}
		
		ATOMIC_BLOCK(ATOMIC_RESTORESTATE){
			MeasurementData.zones = num_zones();
		}
		
		u16 = get_moisture(0);
		
		ATOMIC_BLOCK(ATOMIC_RESTORESTATE){
			MeasurementData.moisture_z0 = u16;
		}
		
		if(LEDBlink){
			set_led(LED_GREEN);
			LEDBlink = 0;
			_delay_ms(1000);
			set_led(LED_OFF);
			_delay_ms(4000);
		} else {
			_delay_ms(5000);
		}
		
	}
		
	return(0);
}