>NAME >NAME >NAME >NAME >NAME >VALUE >NAME >VALUE >NAME >VALUE >Value >Name >Name >Value >Name >Value <b>Panasonic Aluminium Electrolytic Capacitor VS-Serie Package G</b> >NAME >VALUE <b>Panasonic Aluminium Electrolytic Capacitor VS-Serie Package E</b> >NAME >VALUE <b>Panasonic Aluminium Electrolytic Capacitor VS-Serie Package E</b> >NAME >VALUE >NAME >VALUE >NAME >VALUE >Value >Name >Value >Name >NAME >VALUE >NAME >VALUE Type J2 package for SMD supercap PRT-10317 (p# EEC-EN0F204J2) >NAME >VALUE <h3>EIA3528-KIT</h3> <b>Warning:</b> This is the KIT version of this package. This package has longer pads to make hand soldering easier.<br> >NAME >VALUE <h3>EIA3216-KIT</h3> <b>Warning:</b> This is the KIT version of this package. This package has longer pads to make hand soldering easier.<br> >NAME >VALUE >NAME + + >NAME >VALUE >NAME >VALUE + - + >NAME >NAME >VALUE >NAME >VALUE >NAME >VALUE RJ-12 >NAME >VALUE >NAME >VALUE >NAME >VALUE >VALUE >NAME >VALUE >NAME >VALUE >NAME >VALUE <b>Capacitor Polarized</b> These are standard SMD and PTH capacitors. Normally 10uF, 47uF, and 100uF in electrolytic and tantalum varieties. Always verify the external diameter of the through hole cap, it varies with capacity, voltage, and manufacturer. The EIA devices should be standard. <b>Capacitor</b> Standard 0603 ceramic capacitor, and 0.1" leaded capacitor. <h3>SparkFun Electronics' preferred foot prints</h3> We've spent an enormous amount of time creating and checking these footprints and parts. If you enjoy using this library, please buy one of our products at www.sparkfun.com. <br><br> <b>Licensing:</b> CC v3.0 Share-Alike You are welcome to use this library for commercial purposes. For attribution, we ask that when you begin to sell your device using our footprint, you email us with a link to the product being sold. We want bragging rights that we helped (in a very small part) to create your 8th world wonder. We would like the opportunity to feature your device on our homepage. >NAME >VALUE >NAME >VALUE 2mm SMD side-entry connector. tDocu layer indicates the actual physical plastic housing. +/- indicate SparkFun standard batteries and wiring. >Name >Value + - >Name >Value >NAME >VALUE >NAME >VALUE This footprint was designed to help hold the alignment of a through-hole component (i.e. 6-pin header) while soldering it into place. You may notice that each hole has been shifted either up or down by 0.005 of an inch from it's more standard position (which is a perfectly straight line). This slight alteration caused the pins (the squares in the middle) to touch the edges of the holes. Because they are alternating, it causes a "brace" to hold the component in place. 0.005 has proven to be the perfect amount of "off-center" position when using our standard breakaway headers. Although looks a little odd when you look at the bare footprint, once you have a header in there, the alteration is very hard to notice. Also, if you push a header all the way into place, it is covered up entirely on the bottom side. This idea of altering the position of holes to aid alignment will be further integrated into the Sparkfun Library for other footprints. It can help hold any component with 3 or more connection pins. >NAME >VALUE >NAME >VALUE >NAME >VALUE >Name >Value + - >NAME >VALUE >Name >Value + - <H3>JST-2-PTH-KIT</h3> 2-Pin JST, through-hole connector<br> <br> <b>Warning:</b> This is the KIT version of this package. This package has a smaller diameter top stop mask, which doesn't cover the diameter of the pad. This means only the bottom side of the pads' copper will be exposed. You'll only be able to solder to the bottom side. >Name >Value + - >NAME >VALUE >Name >Value <b>RESISTOR</b><p> chip >NAME >VALUE >NAME >VALUE >NAME >VALUE <b>CAPACITOR</b><p> chip >NAME >VALUE 1/6W Thru-hole Resistor - *UNPROVEN* >NAME >VALUE >NAME >VALUE 1/4W Resistor, 0.4" wide<p> Yageo CFR series <a href="http://www.yageo.com/pdf/yageo/Leaded-R_CFR_2008.pdf">http://www.yageo.com/pdf/yageo/Leaded-R_CFR_2008.pdf</a> >Name >Value 1/2W Resistor, 0.5" wide<p> Yageo CFR series <a href="http://www.yageo.com/pdf/yageo/Leaded-R_CFR_2008.pdf">http://www.yageo.com/pdf/yageo/Leaded-R_CFR_2008.pdf</a> >Name >Value 1W Resistor, 0.6" wide<p> Yageo CFR series <a href="http://www.yageo.com/pdf/yageo/Leaded-R_CFR_2008.pdf">http://www.yageo.com/pdf/yageo/Leaded-R_CFR_2008.pdf</a> >Name >Value 2W Resistor, 0.8" wide<p> Yageo CFR series <a href="http://www.yageo.com/pdf/yageo/Leaded-R_CFR_2008.pdf">http://www.yageo.com/pdf/yageo/Leaded-R_CFR_2008.pdf</a> >Name >Value <h3>AXIAL-0.3-KIT</h3> Commonly used for 1/4W through-hole resistors. 0.3" pitch between holes.<br> <br> <b>Warning:</b> This is the KIT version of the AXIAL-0.3 package. This package has a smaller diameter top stop mask, which doesn't cover the diameter of the pad. This means only the bottom side of the pads' copper will be exposed. You'll only be able to solder to the bottom side. >Name >Value >VALUE >NAME >NAME >VALUE <b>Header 2</b> Standard 2-pin 0.1" header. Use with straight break away headers (SKU : PRT-00116), right angle break away headers (PRT-00553), swiss pins (PRT-00743), machine pins (PRT-00117), and female headers (PRT-00115). Molex polarized connector foot print use with SKU : PRT-08233 with associated crimp pins and housings. <b>Resistor</b> Basic schematic elements and footprints for 0603, 1206, and PTH resistors. USB <-> Sense/Net (RS485) Bridge Rev. 1 - Designed by Nick Ames Copyright 2015 OSU CGRB, Tyler Lab, and Jaiswal Lab